Bridges

views updated

Bridges

Forces acting on a bridge

Dynamic loads

Model testing

Types of bridges

Cantilever bridges

Trusses

Arch bridges

Suspension bridges

Pontoon bridges

Movable bridges

Resources

Bridges are structures that join two otherwise inaccessible points of land, such as the two shores of a river or lake, or the two sides of a canyon or deep gully. Bridges are designed to carry railroad cars, motor vehicle traffic, or foot travel by pedestrians

and/or animals, or to support pipes, troughs, or other conduits used for the movement of goods and materials, such as an oil pipeline or a wateraqueduct.

Humans have been constructing bridges since ancient times. The earliest bridges were probably nothing more than felled trees used to cross rivers or ditches. As civilization advanced, artisans discovered ways to use stone, rock, mortar, and other naturally occurring materials in the construction of longer and stronger bridges. Finally, as physicists and engineers began to develop the principles underlying bridge construction, they incorporated other materials such as iron, steel, and aluminum into the bridges they built.

Bridges can be classified in a number of different ways, according to their intended use (railroad bridge or pedestrian walkway, for example), according to the material of which they are made (steel, wood, or concrete), or according to whether they are fixed or moveable. Moveable bridges are used when the height of ships traveling on a waterway will be greater than the bridge floor. In such cases, the bridge is built so that the roadway can be raised or pivoted to allow marine traffic to pass under or through it. Probably the most useful way to classify bridges for technical purposes, however, is according to their structural form. There are three major types of bridges: arch, cantilever, and suspension.

Forces acting on a bridge

Three kinds of forces operate on any bridge: the dead load, the live load, and the dynamic load. The first of these terms refers to the weight of the bridge itself. Like any other structure, a bridge has a tendency to collapse simply because of the gravitational forces acting on the materials of which the bridge is constructed (i.e., the wood, concrete, steel, or aluminum). The second term refers to traffic that moves across the bridge as well as normal environmental factors such as changes in temperature, precipitation, and winds. The third factor refers to environmental factors that go beyond normal weather conditions, factors such as sudden gusts of wind and earthquakes. All three factors must be taken into consideration in the design of a bridge.

For example, suppose that it is necessary to build a bridge across a span that is 325 feet (100 m) wide. It would not be possible to build a beam bridge, one that consists of a single slab of steel of that length. The weight of the material used to construct the bridge plus the weight of the traffic on the bridge would be too great for the bridge to remain standing. An engineer would have to design some other kind of bridge—an arch or suspension bridge, for example—that would be able to hold up that amount of weight.

Dynamic loads

Dynamic loads can present special problems for the designer. A bridge must be able to withstand not only the forces of normal everyday traffic, but also unusual forces of unexpected magnitude. In California, as an example, bridges require special kinds of reinforcement to withstand possible earthquakes. The fact that engineers have not completely solved the problems presented by dynamic loads is reconfirmed from time to time. For example, during the 1989 earthquake in the San Francisco Bay area, a section of the San Francisco–Oakland Bay Bridge collapsed, leaving a gaping hole. A freeway overpass in Oakland also failed during the earthquake, taking the lives of about two dozen motorists.

Wind gusts have been responsible for a number of bridge failures in the past. Even if wind speeds are relatively low, dynamic loads may become too great for a bridge to withstand. One reason for this phenomenon is that the bridge may begin to vibrate so violently that it actually shakes itself apart. Such was the case, for example, with the Tacoma Narrows Bridge in 1941. On November 7 of that year, with wind speeds registering only about 40 mph (25 km/h), the bridge vibrated so badly that it collapsed. The actual force experienced by the bridge was considerably less than the dead and live forces for which it had been designed. But the oscillations produced by wind gusts on the day in question were sufficient to shake the bridge apart.

As a result of failures such as those in the Bay Bridge and the Tacoma Narrows Bridge, engineers have developed methods for making bridges more aerodynamically sound. For example, lighter materials arranged in geometric structures that are more aerodynamically stable are now used in bridges where earthquakes, wind gusts, or other unusually severe environmental problems can be expected.

Model testing

At one time, the only test of a bridge design was actual use. Engineers could incorporate all the scientific knowledge and technological craftsmanship they had to produce a sound design. But how well the bridge would stand up under actual use and dynamic loads could only be discovered in the real world.

Today, engineers have two powerful tools with which to test their ideas: wind tunnels and computer-aided design (CAD). Wind tunnels have long been used by aeronautical engineers to test aircraft designs. Now they are routinely used also for bridge designs. A wind tunnel is an enclosed space in which rapidly moving air from giant fans passes over the model of a bridge. Possible structural and design problems can be detected by photographing and studying patterns of air movement over the model.

As in so many other fields, bridge design has benefited greatly from the growth and development of computer programs. Such programs can incorporate huge amounts of information about various ways in which bridges and the materials of which they are made will react to various kinds of stresses. CAD can be used to draw and test bridge designs on screen without even making the models needed for wind tunnel testing.

Types of bridges

The simplest type of bridge corresponds to the felled tree mentioned above: a single piece of material that stretches from one side of the gap to be bridged to the other. That piece of material—the beam, or girder—rests directly on the ground on each side or is supported on heavy foundations known as piers. The length of a beam bridge of this kind is limited by the weight of the beam itself plus the weight of the traffic it has to bear. Longer beam bridges can be constructed by joining a number of beams to each other in parallel sections.

The concept of a beam bridge can be extended to make a stronger product, the continuous bridge. A continuous bridge differs from a beam bridge in that the latter has at least one additional point of support beyond the two found in a beam bridge. The longest existing continuous bridges now in use are the Astoria Bridge that crosses the Columbia River near Astoria, Oregon, and the Oshima Bridge that connects Oshima Island to the mainland in Japan.

Cantilever bridges

A cantilever bridge is a variation of the simple beam bridge. A cantilever is a long arm that is anchored at one end and is free to move at the opposite end. A diving board is an example of a cantilever. When anchored firmly, a cantilever is a very strong structure. Imagine a 200-pound (91 kg) man standing on the end of diving board. The board bends only slightly, showing that it can hold a relatively large weight (the man).

A cantilever bridge consists of three parts: the outer beams, the cantilevers, and the central beam. Each of the outer beams of the bridge is somewhat similar to a short-beam bridge. The on-shore edge of the bridge is attached to the ground itself or to a pier that is sunk into the ground. The opposite edge of the outer beam is attached to a second pier, sunk into the ground at some distance from the shore.

Bridge piers are vertical columns, usually made of reinforced concrete or some other strong material. In many cases, they are sunk into massive supporting structures known as abutments. Abutments are constructed in large holes in the ground, in contact with bedrock if possible, to withstand the forces created by the dead and live loads created by bridges and the traffic they carry.

Also attached to the off-shore pier is one end of a cantilever. The free end of the cantilever extends outward into the middle of the gap between the shores. An incomplete cantilever bridge consists, therefore, of two halves—one anchored to each side of the gap to be bridged and consisting of a cantilever facing toward the middle of the gap. The space between the two cantilevers, finally, is bridged by another beam, similar to that of a short beam bridge joining the two cantilevers to each other.

The distribution of forces in a cantilever bridge is fairly straightforward. The dead and live loads are borne by the two sets of piers that hold up the bridge, the outermost piers that hold up the outer edges of the bridge, and the inner piers that anchor the fixed end of the cantilever.

The two longest cantilever bridges in the world are the Forth Railway Bridge in Scotland, completed in 1890, and the Quebec Bridge in Canada, built in 1917. The former is 1,700 feet (520 m) in length and the latter, 1,800 feet (550 m) long.

Trusses

The strength of a cantilever bridge can be increased by the use of trusses. A truss is structure that consists of a number of triangles joined to each other. The triangle is an important component of many kinds of structures because it is the only geometric figure that cannot be pulled or pushed out of shape without actually changing the length of one of its sides. By combining a number of triangles into a single unit, the unit is given a great deal of strength.

The cantilever beam, end beams, and joining beams in a cantilever bridge are often strengthened by adding trusses to them. The trusses act somewhat like an extra panel of iron or steel, adding strength to the bridge with relatively little additional weight. The open structure of a truss also allows the wind to blow through them, preventing additional stress on the bridge from this factor.

Trusses are used not only in cantilever bridges, but in all other kinds of bridges also. In fact, you have probably noticed the complex pattern of intersecting triangles on bridges over which you have passed. These truss patterns are one of the most efficient ways of adding strength to any type of bridge an engineer designs.

Arch bridges

As its name suggests, the main supporting structure in an arch bridge is one or more curved elements. The dead and live forces that act on the arch bridge are transmitted along the curved line of the arch into abutments at either end. These abutments are sunk deep into the earth, into bedrock if at all possible.

They are, therefore, essentially immovable and able to withstand very large forces exerted on the bridge itself. This structure is so stable that piers are generally unnecessary in an arch bridge.

The deck of an arch bridge can be placed anywhere with relationship to the arch: on top of it, beneath it, or somewhere within the arch. The deck is attached to the arch by vertical posts (ribs and columns) if the deck is above the arch, by ropes or cables (suspenders) if the deck is below the arch, and by some combination of the two if the deck is somewhere within the arch.

Most arch bridges today are made either of steel or of reinforced concrete. The longest existing steel arch bridge is the New River Gorge Bridge in Fayetteville, West Virginia, built in 1977. It is 1,700 feet (518 m) long. The longest reinforced concrete bridge is the Jesse H. Jones Memorial Bridge at the Houston Ship Channel, Texas, with a length of 1,500 feet (455 m).

Suspension bridges

The longest bridges in the world are suspension bridges. Some examples are the Humber Bridge in Hull, England, with a length of 4,626 feet (1,410 m), the Verrazano Narrows Bridge in lower New York Bay (4,620 feet [1,298 m]); the Golden Gate Bridge over the entrance to San Francisco Bay (4,200 feet [1,280 m]); and the Mackinac Straits Bridge connecting the Upper and Lower Peninsulas of Michigan (3,800 feet [1,158 m]).

In a suspension bridge, the dead and live loads are carried by thick wire cables that run across the top of at least two towers and are anchored to the shorelines within heavy abutments. In some cases, the bridge deck is supported directly by suspenders from the cables, while in other cases, the suspenders are attached to a truss, on top of which the deck is laid. In either case, the dead and light load of the bridge is transmitted to the cables which, in turn, exert stress on the abutments. That stress is counteracted by attaching the abutments to bedrock.

The towers in a suspension bridge typically rest on massive foundations sunk deep into the river or sea bed beneath the bridge itself. The wire cables that carry the weight of the bridge and its traffic are made of parallel strands of steel wire woven together to make a single cable. Such cables typically range in diameter from about 15 inches (38 cm) to as much as 36 inches (91 cm). Smaller cables can be ordered from a factory, while thicker cables may have to be assembled on the construction site itself.

An interesting hybrid of the cantilever and suspension bridge is known as the cable-stayed bridge. The 1,200-foot (366-m) Sunshine Skyway across the entrance to Tampa Bay in Florida is one of the most beautiful examples of the cable-stayed bridge. In a cable-stayed bridge, the deck is cantilevered outward in both directions from a central tower. The deck is then attached to the tower by a series of cables, similar to those in a suspension bridge. Often, a cable-stayed bridge will make use of two towers. In that case, the cantilevered sections extending towards each other in the middle of the bridge can be joined together, producing an unusually long central span. The advantage of the cable-stayed bridge is that support for dead and live loads come from three distinct places: the towers, the cables, and the abutments to which the bridge is attached at each end.

Pontoon bridges

Pontoon bridges float on water. They find use primarily in two situations: First, they find application during wars when engineers need to construct a simple bridge quickly and easily. In such instances, they can be assembled from inflatable rubber or plastic and put into place in a matter of hours. Second, they can be used in rivers and lakes where the river bottom makes it very difficult or impossible to install piers. Lake Washington, in the state of Washington, for example, once had three floating bridges. All were made of large hollow concrete blocks tied to each other.

Movable bridges

Traditionally, three kinds of movable bridges have been constructed. In one, the swing bridge, the deck is rotated around a central span, a large, heavy pier sunk into the river bottom. The swing bridge has one serious disadvantage: The central pier, on which the bridge rotates, is usually located in the deepest part of the waterway. Ships with significant drafts may, therefore, have difficulty passing through such bridges. The swing bridge also has one important advantage: Since it never moves upward, it will not interfere with air traffic that might be present in the area.

In the second type of movable bridge, the bascule bridge, the deck is raised, either at one end or at two ends. The bascule bridge acts, therefore, something like a cantilever in which the free end is raised to permit passage of seagoing vessels.

In the third type of movable bridge, the vertical-lift bridge, the whole central portion is raised straight up by means of steel ropes. One disadvantage of the vertical-lift bridge, of course, is that it can not open

KEY TERMS

Abutment— Heavy supporting structures usually attached to bedrock and supporting bridge piers.

Cable-stayed bridge— A type of bridge that is a mix of cantilever and suspension bridge, in which the deck is supported both by one or more central towers and cables suspended from the tower(s).

Dead load— The force exerted by a bridge as a result of its own weight.

Dynamic load— The force exerted on a bridge as a result of unusual environmental factors, such as earthquakes or strong gusts of wind.

Live load— The force exerted on a bridge as a result of the traffic moving across the bridge. Piers—Vertical columns, usually made of reinforced concrete or some other strong material, on which bridges rest.

Suspenders— Ropes or steel wires from which the deck of a bridge is suspended.

Truss— A very light, yet extremely strong structural form consisting of triangular elements, usually made of iron, steel, or wood.

entirely above the waterway, but can only be raised to a given maximum height.

Resources

BOOKS

Brash, Sarah, Matthew Cope, Charles Foran, Do´nal Kevin Gordon, and Peter Pocock. How Things Work: Structures. Alexandria, VA: Time-Life Books, 1991.

“Bridge,” McGraw-Hill Encyclopedia of Science & Technology. 7th ed. New York: McGraw-Hill Book Company, 1992, volume 2, pp. 49-58.

Corbett, Scott. Bridges. New York: Four Winds Press, 1978. DeLony, Eric. Landmark American Bridges. Boston: Little, Brown and Company, 1993.

MacGregor, Anne and Scott. Bridges: A Project Book. New York: Lothrop, Lee & Shephard Books, 1980.

Trefil, James. Encyclopedia of Science and Technology. The Reference Works, Inc., 2001.

OTHER

Brantacan. “Bridges” <http://www.brantacan.co.uk/bridges.htm> (accessed November 6, 2006).

Public Broadcasting Service (PBS). “Building Big: Bridges” <http://www.pbs.org/wgbh/buildingbig/bridge/index.html> (accessed November 6, 2006).

David E. Newton

More From encyclopedia.com