Skip to main content

Night Vision Scopes

Night Vision Scopes

LARRY GILMAN

Night vision scopes are devices that enable machines or people to "see in the dark," that is, to form images when illumination in the visible band of the electromagnetic spectrum is inadequate. Although it is not possible to form images in absolute darkness, that is, in the absence of any electromagnetic radiation whatsoever, it is possible to form images from radiation wavelengths to which the human eye is insensitive, or to amplify visible-light levels so low that they appear dark to the human eye.

There are two basic approaches to imaging scenes in which visible light is inadequate for human vision:

(1) Low-level visible light that is naturally present may be amplified and presented directly to the viewer's eye. (Light in the near-infrared part of the electromagnetic spectrum [>.771.0 microns], either naturally present or supplied as illumination, may also be amplified and its pattern translated into a visible-light pattern for the viewer's benefit.) This technique is termed image intensification.

(2) Light in the infrared part of the spectrum (>.8 microns) is emitted by all warm objects and may be sensed by electronic devices. A visible-light image can then be produced for the user's benefit on a video screen. This technique is termed thermal imaging.

Image intensification. Image intensification, the method used for the devices termed night-vision scopes, exist in a variety of forms and can be mounted on weapons or vehicles or worn as goggles by an individual. Image-intensification devices have been used by technologically advanced military organizations since the 1950s. In a modern, high-performance light amplifier, light from the scene is collimatedforced to become a mass of parallel raysby being passed through a thin disk comprised of thousands of short, narrow glass cylinders (optical fibers)

packed side by side. The parallel rays of light emerging from these optical fibers are directed at a second disk of equal size, the microchannel plate. The microchannel plate is also comprised of thousands of short, narrow cylinders (.0125mm diameter, about one fourth the diameter of a human hair), but these microchannels are composed of semiconducting crystal rather than optical fiber. A voltage difference is applied between the ends of each microchannel. When a photon (the minimal unit of light, considered as a particle) strikes the end of a microchannel, it knocks electrons free from the atoms in the semiconducting crystal. These are pulled toward the voltage at the far end of the microchannel, knocking more electrons loose as they move through the crystal matrix. Thousands of electrons can be produced in a microchannel by the arrival of a single photon. At the far end of the microchannel, these electrons strike a phosphor screen that is of the same size and shape as the microchannel disk. The phosphor screen contains phosphor compounds that emit photons in the green part of the visible spectrum when struck by electrons; thus, that part of the phosphor disk affected by a single microchannel glows visibly, the brightness of its glow being in proportion to the intensity of the electron output of the microchannel. (Green is chosen because the human eye can distinguish brightness variations in green more efficiently than in any other color.) The phosphor-disk image is comprised of millions of closely packed dots of light, each corresponding to the electron output of a single microchannel. The light from the phosphor disk is collimated by a second fiber-optic disk and presented to the viewer's eye through a lens. The function of the lens is to allow the user's eye to relax (i.e., focus at infinity), rather than straining to focus on an image only an inch or so away. Alternatively, the phosphor-disk image can be filmed by a camera.

A pair of night-vision goggles may contain two such systems, either one for each eye, or, as in the case of the U.S. Army's AN/PVS-7B night vision goggles, a single image may be split into identical copies and presented to both the user's eyes simultaneously.

A "third generation" image intensifier has been described above; several other image-intensification technologies remain in the field. All, however, operate by using photons to liberate electrons, amplifying the resulting electron current, and using the amplified electron current to liberate visible photons.

Image intensifiers form sharp images with natural contrast patterns. Also, they use very little power and so can run for many hours on, say, a battery mounted in a helmet. Because they are relatively cheap and can provide a mobile individual with the ability to see in most "dark" conditions, hundreds of thousands of night-vision goggles and scopes based on image intensification have been sold to military and police forces worldwide. Criminals have also been using them increasingly, as a number of models are now available on the consumer market. However, night-vision goggles provide poor peripheral vision, which can disorient pilots or drivers. Further, they cannot work in settings where visible and near-infrared light are truly absent (e.g., inside a windowless building). The latter disadvantage can only be partly offset by providing active illumination (e.g., a laser), because such light sources reveal themselves to enemy forces equipped with image intensifiers.

Infrared imaging. Image intensification amplifies radiation reflected by objects; infrared imaging works by detecting radiation emitted by objects. All objects at non-cryogenic temperatures glow spontaneously in the infrared region of the spectrum. Air is opaque to some of this radiation, but has two wavelength "windows" through which infrared radiation passes freely: the 35 micron window and the 812 micron window. (One micron is a millionth of a meter.)

Semiconductor devices sensitive to infrared radiation in either of the two atmospheric infrared windows can be built, in large numbers, on the surface of a chip. An infrared image focused on the surface of such an array can be read off electronically as image information, which is then used to construct a visible-light image on a screen.

Infrared imaging systems are bulkier and more expensive than image intensification systems. However, they work even in a complete absence of illumination (since all scenes "glow" in infrared) and can detect otherwise invisible phenomena, such as hot, nonsmoky exhaust plumes or buried landmines, that may be of military or security interest. Infrared imagers are also used for a wide variety of forensic and industrial purposes, as they can reveal chemical compositional differences not evident in visible light.

FURTHER READING:

BOOKS:

Schlessinger, Monroe. Infrared Technology Fundamentals. New York: Marcel Dekker, Inc., 1995.

PERIODICALS:

Owens, Ken, and Larry Matthies. "Passive Night Vision Sensor Comparison for Unmanned Ground Vehicle Stereo Vision Navigtaion," in proceedings from the International Conference on Robotics and Automation. (2000): 122131.

Thompson, R. J. "New Developments in Night-Vision Equipment and Techniques," in proceedings from the 1995 International Carnahan Conference on Security Technology. (2000): 144446.

Cite this article
Pick a style below, and copy the text for your bibliography.

  • MLA
  • Chicago
  • APA

"Night Vision Scopes." Encyclopedia of Espionage, Intelligence, and Security. . Encyclopedia.com. 14 Aug. 2018 <http://www.encyclopedia.com>.

"Night Vision Scopes." Encyclopedia of Espionage, Intelligence, and Security. . Encyclopedia.com. (August 14, 2018). http://www.encyclopedia.com/politics/encyclopedias-almanacs-transcripts-and-maps/night-vision-scopes

"Night Vision Scopes." Encyclopedia of Espionage, Intelligence, and Security. . Retrieved August 14, 2018 from Encyclopedia.com: http://www.encyclopedia.com/politics/encyclopedias-almanacs-transcripts-and-maps/night-vision-scopes

Learn more about citation styles

Citation styles

Encyclopedia.com gives you the ability to cite reference entries and articles according to common styles from the Modern Language Association (MLA), The Chicago Manual of Style, and the American Psychological Association (APA).

Within the “Cite this article” tool, pick a style to see how all available information looks when formatted according to that style. Then, copy and paste the text into your bibliography or works cited list.

Because each style has its own formatting nuances that evolve over time and not all information is available for every reference entry or article, Encyclopedia.com cannot guarantee each citation it generates. Therefore, it’s best to use Encyclopedia.com citations as a starting point before checking the style against your school or publication’s requirements and the most-recent information available at these sites:

Modern Language Association

http://www.mla.org/style

The Chicago Manual of Style

http://www.chicagomanualofstyle.org/tools_citationguide.html

American Psychological Association

http://apastyle.apa.org/

Notes:
  • Most online reference entries and articles do not have page numbers. Therefore, that information is unavailable for most Encyclopedia.com content. However, the date of retrieval is often important. Refer to each style’s convention regarding the best way to format page numbers and retrieval dates.
  • In addition to the MLA, Chicago, and APA styles, your school, university, publication, or institution may have its own requirements for citations. Therefore, be sure to refer to those guidelines when editing your bibliography or works cited list.