Porcelain

views updated May 23 2018

Porcelain

Background

The term porcelain refers to a wide range of ceramic products that have been baked at high temperatures to achieve vitreous, or glassy, qualities such as translucence and low porosity. Among the most familiar porcelain goods are table and decorative china, chemical ware, dental crowns, and electrical insulators. Usually white or off-white, porcelain comes in both glazed and unglazed varieties, with bisque, fired at a high temperature, representing the most popular unglazed variety.

Although porcelain is frequently used as a synonym for china, the two are not identical. They resemble one another in that both are vitreous wares of extremely low porosity, and both can be glazed or unglazed. However, china, also known as soft-paste or tender porcelain, is softer: it can be cut with a file, while porcelain cannot. This difference is due to the higher temperatures at which true porcelain is fired, 2,650 degrees Fahrenheit (1,454 degrees Celsius) compared to 2,200 degrees Fahrenheit (1,204 degrees Celsius) for china. Due to its greater hardness, porcelain has some medical and industrial applications which china, limited to domestic and artistic use, does not. Moreover, whereas porcelain is always translucent, china is opaque.

Hard-paste or "true" porcelain originated in China during the T'ang dynasty (618-907 A.D.); however, high quality porcelain comparable to modern wares did not develop until the Yuan dynasty (1279-1368 A.D.). Early Chinese porcelain consisted of kaolin (china clay) and pegmatite, a coarse type of granite. Porcelain was unknown to European potters prior to the importation of Chinese wares during the Middle Ages. Europeans tried to duplicate Chinese porcelain, but, unable to analyze its chemical composition, they could imitate only its appearance. After mixing glass with tin oxide to render it opaque, European craftspeople tried combining clay and ground glass. These alternatives became known as soft-paste, glassy, or artificial porcelains. However, because they were softer than genuine porcelain, as well as expensive to produce, efforts to develop true porcelain continued. In 1707 two Germans named Ehrenfried Walter von Tschimhaus and Johann Friedrich Bottger succeeded by combining clay with ground feldspar instead of the ground glass previously used.

Later in the eighteenth century the English further improved upon the recipe for porcelain when they invented bone china by adding ash from cattle bones to clay, feldspar, and quartz. Although bone china is fired at lower temperatures than true porcelain, the bone ash enables it to become translucent nonetheless. Because it is also easier to make, harder to chip, and stronger than hard porcelain, bone china has become the most popular type of porcelain in the United States and Britain (European consumers continue to favor hard porcelain).

Raw Materials

The primary components of porcelain are clays, feldspar or flint, and silica, all characterized by small particle size. To create different types of porcelain, craftspeople combine these raw materials in varying proportions until they obtain the desired green (unfired) and fired properties.

Although the composition of clay varies depending upon where it is extracted and how it is treated, all clays vitrify (develop glassy qualities), only at extremely high temperatures unless they are mixed with materials whose vitrification threshold is lower. Unlike glass, however, clay is refractory, meaning that it holds its shape when it is heated. In effect, porcelain combines glass's low porosity with clay's ability to retain its shape when heated, making it both easy to form and ideal for domestic use. The principal clays used to make porcelain are china clay and ball clay, which consist mostly of kaolinate, a hydrous aluminum silicate.

Feldspar, a mineral comprising mostly aluminum silicate, and flint, a type of hard quartz, function as fluxes in the porcelain body or mixture. Fluxes reduce the temperature at which liquid glass forms during firing to between 1,835 and 2,375 degrees Fahrenheit (1,000 and 1,300 degrees Celsius). This liquid phase binds the grains of the body together.

Silica is a compound of oxygen and silicon, the two most abundant elements in the earth's crust. Its resemblance to glass is visible in quartz (its crystalline form), opal (its amorphous form), and sand (its impure form). Silica is the most common filler used to facilitate forming and firing of the body, as well as to improve the properties of the finished product. Porcelain may also contain alumina, a compound of aluminum and oxygen, or low-alkali containing bodies, such as steatite, better known as soapstone.

The Manufacturing
Process

After the raw materials are selected and the desired amounts weighed, they go through a series of preparation steps. First, they are crushed and purified. Next, they are mixed together before being subjected to one of four forming processessoft plastic forming, stiff plastic forming, pressing, or casting; the choice depends upon the type of ware being produced. After the porcelain has been formed, it is subjected to a final purification process, bisque-firing, before being glazed. Glaze is a layer of decorative glass applied to and fired onto a ceramic body. The final manufacturing phase is firing, a heating step that takes place in a type of oven called a kiln.

Crushing the raw materials

  • 1 First, the raw material particles are reduced to the desired size, which involves using a variety of equipment during several crushing and grinding steps. Primary crushing is done in jaw crushers which use swinging metal jaws. Secondary crushing reduces particles to 0.1 inch (.25 centimeter) or less in diameter by using mullers (steel-tired wheels) or hammer mills, rapidly moving steel hammers. For fine grinding, craftspeople use ball mills that consist of large rotating cylinders partially filled with steel or ceramic grinding media of spherical shape.

Cleaning and mixing

  • 2 The ingredients are passed through a series of screens to remove any under- or over-sized materials. Screens, usually operated in a sloped position, are vibrated mechanically or electromechanically to improve flow. If the body is to be formed wet, the ingredients are then combined with water to produce the desired consistency. Magnetic filtration is then used to remove iron from the slurries, as these watery mixtures of insoluble material are called. Because iron occurs so pervasively in most clays and will impart an undesirable reddish hue to the body if it oxidizes, removing it prior to firing is essential. If the body is to be formed dry, shell mixers, ribbon mixers, or intensive mixers are typically used.

Forming the body

  • 3 Next, the body of the porcelain is formed. This can be done using one of four methods, depending on the type of ware being produced:
    • soft plastic forming, where the clay is shaped by manual molding, wheel throwing, jiggering, or ram pressing. In wheel throwing, a potter places the desired amount of body on a wheel and shapes it while the wheel turns. In jiggering, the clay is put on a horizontal plaster mold of the desired shape; that mold shapes one side of the clay, while a heated die is brought down from above to shape the other side. In ram pressing, the clay is put between two plaster molds, which shape it while forcing the water out. The mold is then separated by applying vacuum to the upper half of the mold and pressure to the lower half of the mold. Pressure is then applied to the upper half to free the formed body.
    • stiff plastic forming, which is used to shape less plastic bodies. The body is forced through a steel die to produce a column of uniform girth. This is either cut into the desired length or used as a blank for other forming operations.
    • pressing, which is used to compact and shape dry bodies in a rigid die or flexible mold. There are several types of pressing, based on the direction of pressure. Uniaxial pressing describes the process of applying pressure from only one direction, whereas isostatic pressing entails applying pressure equally from all sides.
    • slip casting, in which a slurry is poured into a porous mold. The liquid is filtered out through the mold, leaving a layer of solid porcelain body. Water continues to drain out of the cast layer, until the layer becomes rigid and can be removed from the mold. If the excess fluid is not drained from the mold and the entire material is allowed to solidify, the process is known as solid casting.

Bisque-firing

  • 4 After being formed, the porcelain parts are generally bisque-fired, which entails heating them at a relatively low temperature to vaporize volatile contaminants and minimize shrinkage during firing.

Glazing

  • 5 After the raw materials for the glaze have been ground they are mixed with water. Like the body slurry, the glaze slurry is screened and passed through magnetic filters to remove contaminants. It is then applied to the ware by means of painting, pouring, dipping, or spraying. Different types of glazes can be produced by varying the proportions of the constituent ingredients, such as alumina, silica, and calcia. For example, increasing the alumina and decreasing the silica produces a matte glaze.

Firing

  • 6 Firing is a further heating step that can be done in one of two types of oven, or kiln. A periodic kiln consists of a single, refractory-lined, sealed chamber with burner ports and flues (or electric heating elements). It can fire only one batch of ware at a time, but it is more flexible since the firing cycle can be adjusted for each product. A tunnel kiln is a refractory chamber several hundred feet or more in length. It maintains certain temperature zones continuously, with the ware being pushed from one zone to another. Typically, the ware will enter a preheating zone and move through a central firing zone before leaving the kiln via a cooling zone. This type of kiln is usually more economical and energy efficient than a periodic kiln.
  • 7 During the firing process, a variety of reactions take place. First, carbon-based impurities burn out, chemical water evolves (at 215 to 395 degrees Fahrenheit or 100 to 200 degrees Celsius), and carbonates and sulfates begin to decompose (at 755 to 1,295 degrees Fahrenheit or 400 to 700 degrees Celsius). Gases are produced that must escape from the ware. On further heating, some of the minerals break down into other phases, and the fluxes present (feldspar and flint) react with the decomposing minerals to form liquid glasses (at 1,295 to 2,015 degrees Fahrenheit or 700 to 1,100 degrees Celsius). These glass phases are necessary for shrinking and bonding the grains. After the desired density is achieved (greater than 2,195 degrees Fahrenheit or 1,200 degrees Celsius), the ware is cooled, which causes the liquid glass to solidify, thereby forming a strong bond between the remaining crystalline grains. After cooling, the porcelain is complete.

Quality Control

The character of the raw materials is important in maintaining quality during the manufacturing process. The chemical composition, mineral phase, particle size distribution, and colloidal surface area affect the fired and unfired properties of the porcelain. With unfired body, the properties evaluated include viscosity, plasticity, shrinkage, and strength. With fired porcelain, strength, porosity, color, and thermal expansion are measured. Many of these properties are monitored and controlled during manufacturing using statistical methods. Both the raw materials and the process parameters (milling time and forming pressure, for example) can be adjusted to achieve desired quality.

The Future

High-quality porcelain art and dinnerware will continue to enhance the culture. Improvements in manufacturing will continue to increase both productivity and energy efficiency. For instance, a German kiln manufacturer has developed a prefabricated tunnel kiln for fast firing high-quality porcelain in less than 5 hours. Firing is achieved by partly reducing atmosphere at a maximum firing temperature of 2,555 degrees Fahrenheit (1,400 degrees Celsius). The kiln uses high-velocity burners and an automatic control system, producing 23,000 pounds (11,500 kilograms) of porcelain in 24 hours.

Manufacturers of porcelain products may also have to increase their recycling efforts, due to the increase in environmental regulations. Though unfired scrap is easily recycled, fired scrap poses a problem: mechanically strong and therefore hard to break down, it is usually dumped into landfills. However, preliminary research has shown that fired scrap can be reused after thermal quenching (where the scrap is reheated and then quickly cooled), which makes it weaker and easier to break down. The scrap can then be used as a raw material.

Porcelain appears to be playing a more important role in technical applications. Recent patents have been issued to Japanese and American companies in the area of electrical insulators and dental prostheses. NGK Insulators, Ltd., a Japanese manufacturer, has developed high-strength porcelain for electrical insulators, whereas Murata Manufacturing Co. has developed low-temperature-sintering porcelain components for electronic applications.

Where To Learn More

Books

Campbell, James E. The Art and Architecture Information Guide Series, vol. 7:Pottery and Ceramics, A Guide to Infonnation Sources. Gale Research, 1978.

Camusso, Lorenzo, ed. Ceramics of the World: From Four Thousand b.c. to the Present. Harry N. Abrams, 1992.

Charles, Bernard H. Pottery and Porcelain. Hippocrene Books, 1974.

Jones, J. T. and M. F. Bernard. Ceramics, Industrial Processing and Testing. Iowa State University Press, 1972.

Periodicals

Shashidhar, N. and J. S. Reed. "Recycling Fired Porcelain." Ceramic Bulletin. Vol. 69, No. 5, 1990, pp. 834-841.

Wilson, Lana. "Charcoal and Metallic Salts." Ceramics Monthly. October, 1987, p. 36.

L. S. Millberg

Porcelain

views updated May 23 2018

Porcelain

Sources

Tang Pottery. The strong economy and effective government of the Tang era (618-907), coupled with the Tang dynasty’s openness to foreign influences, stimulated the development of porcelain as early as the seventh century or as late as the early ninth century. The kilns of the Yue region produced greenish-colored porcelain well known for its hardness and craftsmanship. Tang porcelain from the kilns of Xing is white and known for its strength and elegant shapes. The Tang San Cat (The Three Colors of Tang), well-known lead glazes developed in the Tang period, allowed the craftsman to decorate porcelain and other ceramics in yellows (ranging to amber and brown), green, and blue. Tang figurines decorated with Tang San Cai are colorful, and their shapes are rounded, natural, and dynamic.

Song and Yuan Porcelain. During the Song (960-1279) and Yuan (1279-1368) dynasties, economic growth and the flourishing of the arts established a solid foundation for the development of the porcelain industry. Official and unofficial management systems efficiently organized craftsmen through a highly developed division of labor, which allowed the quality and quantity of porcelain and other ceramics to reach new heights. Combining art, craftsman-ship, and utility, many porcelain products appeared in various elegant shapes, bright new colors, and beautiful decorations. Song porcelain in green, white, and black came from many production centers. Ruyao (Ru Kiln), located in and around Linru County of Henan Province, is known for its green porcelain, and the translucent porcelain produced by the official kilns there is exquisite and elegant. The “shrimp green” of Ruyao is among the best green porcelains. The Guanyao (Official Kiln) was established by the Song court in Kaifeng and moved to Hangzhou during the Southern Song dynasty (1127-1279). The porcelain produced by the Official Kiln has a fine, smooth, even glaze in shades of green and milk white. Its thickness creates a translucent quality. The craftsmen at the Longquanyao (Dragon Fountain Kiln) in Longquan County, Zhejiang Province, were masters of technique and produced porcelain carved in relief and glazed with beautiful colors, mostly shades of green. Craftsmen at another kiln in Longquan County, the Geyao (Brothers’ Kiln), invented the popular crackle-glazed porcelain. Jianyao (Strong Kiln) of Chidun Village in Shuiji County, Fujian Province, was the center for black porcelain. The earth there contains a lot of iron, which turns porcelain made from it black during the process of firing and cooling. The black porcelain produced at this site—in patterns with names such as such as Tuhao (Rabbit Hair), Zheguban (Partridge Speckle), and Yinxingban (Silver Star Spots)—had thick, translucent glazes. In contrast, Dingyao (Ding Kiln) in Ding County, Hebei Province, was famous for its white porcelain, which is extremely refined and decorated with various designs and methods of carving.

Jingdezhenyao from the Yuan to the Ming Eras. Jingdezhenyao (Jingdezhen Kiln) at Jingdezhen in Jiangxi developed into a major porcelain center during the Yuan dynasty, and official and nonofficial (or folk) kilns sprang up all over the town. Jingdezhen porcelain is characterized by its elegant, exquisite shapes and beautiful glazes. By the Ming dynasty (1368-1644), Jingdezhen porcelain glazes

came in some fifty-seven colors. Craftsmen there also perfected true-white porcelain and a red porcelain, breakthroughs in the history of Chinese ceramics. They also developed methods of underglaze and overglaze painting, which allowed craftsmen to add many more layers of color to porcelain.

Sources

Craig Chinas, Art in China (Oxford & New York: Oxford University Press, 1997).

Lan Pu, Jingdezhen taolu (Daibei, China: Eastern Culture Press, 1984).

Rosemary E. Scott, ed., The Porcelains of Jingdezhen (London: Percival David Foundation of Chinese Art, 1993).

Laurence Sickman and Alexander Soper, The Art and Architecture of China (New York: Penguin, 1984).

Michael Sullivan, The Arts of China, fourth edition, expanded and revised (Berkeley: University of California Press, 1999).

Wang Qisen, Zhongguoyishu tongshi (Jiangsu: Jiangsu Arts Press, 1999).

Porcelain

views updated Jun 08 2018

PORCELAIN

PORCELAIN. Benjamin Franklin viewed the domestic manufacture of porcelain as an important step toward economic independence from England, and it ultimately became intimately linked with the industrialization of the nation. However, its production in the United States was never as crucial as stoneware and redware production.

Porcelain, first made in China during the Tang dynasty (618–907 a.d.), remained a Chinese secret sought by the West for many hundreds of years. It was not until 1708 and 1709, after the German ceramist Johann Friedrich Böttger had discovered its secret, kaolin, that true hard-paste porcelain was produced outside of China. In 1738, Andrew Duché of Savannah, Georgia, made the first recorded piece of porcelain in North America, "a small teacup … very near transparent."

Around 1825 some twenty skilled craftsmen from England and France were employed to make porcelain for the Jersey Porcelain and Earthenware Company in Jersey City, New Jersey. Other ventures followed in Philadelphia. In 1853, when the Crystal Palace Exhibition of the Industry of All Nations was held in New York City, work by the Haviland Brothers, who had a china shop there, was much praised. By the mid-1860s, Parian ware, a type of porcelain having the appearance of marble, became so popular that no fashionable Victorian parlor would be without a piece or two. Ott and Brewer of Trenton, New Jersey, sold a wide line of Parian ware. From the 1880s on, Belleek, a light, marvelously thin, ivory-colored porcelain variant of Parian, named after its Irish town of origin, became the greatest American ceramics success story.

After the influential Centennial Exhibition in Philadelphia, art pottery became a serious business in America. Porcelain, while a minor branch of the industry, had its champions in M. Louise McLaughlin (1847–1939) and especially Adelaide Alsop Robineau (1865–1929). By the 1930s, porcelain found wide application in industry and began to be studied at colleges, universities, and art schools such as Cranbrook. An intense interest in porcelain continues.

BIBLIOGRAPHY

American Ceramics: The Collection of Everson Museum of Art. New York: Rizzoli, 1989.

Frelinghuysen, Alice Cooney. American Porcelain, 1770–1920. New York: The Metropolitan Museum of Art, 1989.

See alsoArt: Pottery and Ceramics .

porcelain

views updated May 18 2018

por·ce·lain / ˈpôrs(ə)lən/ • n. a white vitrified translucent ceramic; china.See also hard-paste, soft-paste. ∎  (usu. porcelains) articles made of this. ∎  such articles collectively: a collection of Chinese porcelain.DERIVATIVES: por·ce·la·ne·ous / ˌpôrsəˈlānēəs/ adj.por·cel·la·nous / -əs/ adj.

porcelain

views updated May 18 2018

porcelain White, glass-like, non-porous, hard, translucent ceramic. Porcelain is used for tableware, decorative objects, laboratory equipment, and electrical insulators. It was developed by the Chinese in the 7th or 8th century. True or hard-paste porcelain is made of kaolin (white china clay) mixed with powdered petuntse (feldspar) fired at about 1400°C (2550°F). Soft-paste porcelain is made of clay and powdered glass, fired at a low temperature, lead glazed, and refired.

porcelain

views updated May 23 2018

porcelain XVI. The earliest forms in -ana, -an are It. or immed. — It.; superseded by forms — F. porcelaine, earlier pourcelaine — It. porcellana cowrie, polished substance of this, (hence) china ware (from its resemblance to this substance), deriv. in fem. adj. form of porcella, dim. of porca sow:— L. porca, fem. of porcus swine; the shells are said to have been so named from their resemblance to the vulva of a sow.