The critical amount of nitrogen on the formation of nitrogen gas pores during solidification of 25Cr-7Ni duplex stainless steels

From: Metallurgical and Materials Transactions | Date: June 1, 2003| Author: | Copyright information

The effects of casting thickness, nitrogen contents, cooling rate, and Mn contents on the formation of nitrogen gas pores during solidification of 25Cr-7Ni-1.5Mo-3W duplex stainless steels (DSS) were quantitatively investigated. In the case of a sand mold, the formation of nitrogen gas pore was not affected by the thickness of castings, which ranged from 13 to 52 mm, and the critical initial nitrogen content for the formation of gas pore was 0.30 wt pct. In the case of the molds made of a stainless steel (STS) and water-cooled Cu, the critical initial nitrogen content did not change much ...

Read all of this article with a FREE trial to HighBeam Research

Related newspaper, magazine, and trade journal articles from HighBeam Research

(Including press releases, facts, information, and biographies)

A fine gamma' + alpha cellular structure in Fe-37.3 Wt Pct Ni-3.6 Wt Pct Al-3.3 Wt Pct Ti-0.2 Wt Pct C and its influence on high-temperature tensile properties
; Fe-37.3 wt pct Ni-3.6 wt pct Al-3.3 wt pct Ti-0.2 wt pct C alloy, which reveals an excellent combination of high strength and good elongation endowed by formation of homogeneously dispersed fine gamma' precipitates in the matrix during aging at 823...
Thermal transformations in mechanically alloyed Fe-Zn-Si materials
; The ball milling of elemental powders corresponding to F (Fe3Zn10) + 0.12 wt pct Si; F, (Fe5Zn21) + 0.12 wt pct Si; 5 (FeZn7) + 0.12 wt pct Si; and ' (FeZn13) + 0.12 wt pct Si composition ratios yields crystalline, mechanically alloyed...
Ductility and Impact Resistance of Powder-Metallurgical Molybdenum-Rhenium Alloys
; Mo-Re alloys containing between 5 and 47.5 wt pct Re were fabricated from Mo and Mo-Re powders...were examined. Up to a concentration of 41 wt pct Re. the Charpy ductileto-brittle transition...rhenium concentration. Between 10 and 41 wt pct rhenium, the room-temperature tensile ...
On the influence of Si-Ge additions on the aging response of Al-Cu
; ...to the ternary Al-Si-Ge, a dramatic hardening result could be achieved.[1] Alloys of the composition Al5.7 wt pct Cu-0.5 wt pct Si-1.3 wt pct Ge (which is Al-2.5 at. pct Cu-0.5 at. pct Si-0.5 at. pct Ge) and Al-5.4 wt pct Cu-1 wt pct Si-2.63 wt ...
Relationship between tensile and shear strengths of the mushy zone in solidifying aluminum alloys
; Strength development in the mushy zone during solidification of three aluminum alloys (Al-4 wt pct Cu, Al-7 wt pct Si-I wt pct Cu, and Al-7 wt pct Si-4 wt pct Cu) has been measured with two different techniques-horizontal tensile testing...
The rate of reaction of solid iron with oxidized "FeO"-CaO-SiO2-Al2O3 slags at 1360 (degrees)C--the chemical diffusivity of iron oxide
; ...41CaO 38SiO^sub 2^-21Al^sub 2^O^sub 3^ (wt pct) slags at 1360 deg.C by a rotating disc...concentrations of between 1.8 and 13.4 wt pct and rotation speeds up to 1000 rpm, the...empirical expression log D = -6.11 + 0.08 (wt pct Fe). It is concluded that the values of...
Reactive phosphide inclusions in commerical ferrosilicon
; ...commercial ferrosilicon alloys containing ~75 wt pct Si. Based on previous work, it is suspected...ferrosilicon alloys containing greater than 0.1 wt pct (0.1 at. pct) phosphorus. Researchers in...aluminum in synthetically produced Fe-45 wt pct Si and Fe-65 wt pct Si ...
Reactive phosphide inclusions in commercial ferrosilicon
; ...commercial ferrosilicon alloys containing ~75 wt pct Si. Based on previous work, it is suspected...ferrosilicon alloys containing greater than 0.1 wt pct (0.1 at. pct) phosphorus. Researchers in...aluminum in synthetically produced Fe-45 wt pct Si and Fe-65 wt pct Si ...
Primary dendrite distribution and disorder during directional solidification of Pb-Sb alloys
; Pb-2.2 wt pet Sb and Pb-5.8 wt pct Sb alloys have been directionally solidified from a single-cryst...convection in the mushy zone.[10] Two alloy compositions, Pb-5.8 wt pct Sb and Pb-2.2 wt pct Sb, were selected to achieve varying degrees of thermosolutal...
Microstructure and Yield Strength of UDIMET 720LI Alloyed with Co-16.9 Wt Pct Ti
; ...superalloy U720LI with a two-phase alloy Co-16.9 wt pct Ti in various contents. The microstructure...the alloys with the addition of Co-16.9 wt pct Ti, and its volume fraction increased with the increase in the addition of Co-16.9 wt pct Ti. The results of exposure at 750 C show...